![]() ![]() Using marker pen, mark 40mm from the end of the fiber cable.Ĭ. For LC connectors, you also need to slide the trigger onto the fiber cable after sliding the rubber boot.ī. ![]() Slide the strain relief rubber root onto the fiber cable. Redo the above steps if the Error Light turns on. Close the tool cover and check for the Error Light. ![]() ![]() Move the VFL Coupler toward the Connector Cradle so the Ferrule Adapter is seated on the connector.į. You must make sure that the connector sits firmly in the Connector Cradle.ĭ. Guide the connector into the Connector Cradle and slowly release the LOAD button at the same time. Insert the connector lead-in tube into the Wrench as shown below.Ĭ. While keeping the connector the CAM at the correct position as mentioned above, insert the connector into the Pretium Installation tool. Press the LOAD button down in order to move the Connector Cradle away from the Wrench.ī. Keep the black load adapter on LC and ST connectors until after termination. Remove both the rear dust cap and the front clear dust cap.Ĭ. The following picture shows the correct CAM open position for each connector type.ī. Make sure the connector CAM is in the OPEN position since it may rotate during shipping and handling. Move the power switch to ON position to turn on the power. 1.25mm ferrule adapter is for LC connectors.į. 2.5mm ferrule adapter is for SC and ST connectors. Here it shows that the Wrench should be at its start positionĮ. Here it shows the positions various components should be Press the Reset button to reset the Wrench to its start position Put connector cradle to its travel stopĭ. Slide the Visual Fault Locator (VFL) coupler back to the cover hinge until locks.Ĭ. Prepare Installation Toolįirst, look at the Unicam Pretium installation tool and its components.Ģ.50mm Ferrule Adapter (ships in the tool)ġ.25mm Ferrule Adapter (ships in the toolkit)Ī. :: 7 Steps to Install Corning Unicam Connector Step 1. Well, this is a really simplified description. Better yet, you don’t even need epoxy or polishing at all! Congratulations! You have just installed a Unicam Connector. Next using the installation tool, you rotate the cam mechanism to actuate the Unicam connector, and lock the the fiber in place. The index matching gel inside makes a smooth light transmission between the fibers and minimizes the back reflection. The other end of the fiber is cleaved and stays inside the connector body, fully protected.Īll you have to do now is to cleaver your fiber and insert it into the connector body to physically contact with the fiber stub inside. The end face can be polished to different finish, such as PC, UPC and APC. Unicam connector end face is pre-polished in factory with a fiber stub embedded in the connector body. Take a close look at the following picture. This is a big time saving compared to 5~10 minutes for traditional epoxy and polish connectors.īut how does it achieve this? The answer is simple: Unicam connector is pre-polished. Unicam connector is a type of quick termination connectors which takes less two minutes to install. Or click on the following picture to get. This instruction uses the Corning Unicam Pretium Installation Tool Kit to terminate Unicam SC, LC and ST connectors. ParameterĬonnectors are FOCIS compliant with TIA/EIA 604-10A (LC) TIA/EIA 604-3 (SC) TIA/EIA 604-2 (ST Compatible)ġ0 lb ≤ 0.2 dB change on jacketed cable 0.:: How do Corning Unicam connectors work? Note: LOMMF = Laser-optimized multimode fiberġ LC Connectors are sold with one 900 µm boot, one 2.0/1.6 boot, and one 2.9 mm boot SC and ST Compatible connectors are sold with one 900 µm boot and one 2.9 mm boot. They also meet TIA/EIA-568 B.3 specifications for insertion loss and return loss at temperatures of -40° to +75° C, which allows the connectors to be used outdoors when enclosed in environmentally protected hardware. The UniCam Pretium-Performance Multimode Connectors are 100% guaranteed for meeting an installation specification of 0.1 dB typical and 0.5 dB maximum insertion. Pretium performance can be achieved with the UniCam Pretium Tool Kit or the standard UniCam Connector Toolkit.Operating temperature ranges from -40° to +75° C to accommodate indoor or outdoor use in an enclosure.100% guaranteed by Corning Cable Systems to meet insertion loss specification. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |